STANDARD CYLINDERS

Image	Model	Specification	Application	DataSheet
	MCQA	Ø40-Ø200	Non-lubrication High quality-long service life Non-standard type Cylinder mountings	Download
	MCQA-AH	Ø40-Ø150	Cylinder thrust should be 70% (50% of Maximum Speed) of theoretical force. Displacement should be approximately 50% of total volume. Maximum acceleration is approximately 200mm/sec. ISO VG32 or an equivalent oil is recommended. Oil feed should not exceed 80% of total volume. Unit should be installed vertically above the cylinder / actuator.	Download
	MCQN	Ø1 1/2”~Ø4”	Non lubrication High quality long service life Full range of NFPA interchangable mounting configurations	Download
	MCQV	Ø32~Ø200	Non-lubrication High quality-long service life ISO 15552 standard specification Cylinder mountings
	MCQV2L	Ø63,Ø80	Non-lubrication High quality-long service life ISO 15552 standard specification
	MCQI2	Ø32,Ø100	Non-lubrication High quality-long service life ISO 15552 standard specification Easy to insert reed switch
	MCB	Ø32,Ø40	Locking unit is a mechanical device to apply to cylinders ISO 15552 and ISO 6432 whose scope is to block cylinder's rod in any position. This solution allows to block the race of the cylinder anytime takes place an unexpected fall of pressure. The blocking force is always and however greater of the one developed from the respective cylinder at 1 MPa.

Compact Cylinders

Image	Model	Specification	Application	Data sheet
	MCJA	Ø12~Ø100	Multiple Position Back to Back Type
	MCJQ	Ø12~Ø100	Ultra Compact, light weight and space saving cylinder. Wide range of bore sizes and strokes (12mm~100mm).Wide range of bore sizes and strokes (12mm~100mm). Single and double acting available. Ideal for use in machinery where space is limited and incorporating sensor groove which enables flush fitting of sensors. Sensor can be mounted on any one of three faces on 12 and 16 bore and on four faces on 20~100 bore.
	MCKJQ	Ø12~Ø40	No rotation
	MCJQ2	Ø12~Ø25	Ultra Compact, light weight and space saving cylinder. Single and double acting available. Ideal for use in machinery where space is limited and incorporating sensor groove which enables flush fitting of sensors. Magnetic as standard.
	MCJI	Ø20~Ø100	Multiple Position
	MCJU	Ø25~Ø6	Plate type design for ultra compact, Oval piston design for non-rotation and space saving. Sensor slots on sides for flush mounting of proximity sensors. Magnetic as standard.
	MCFA	Ø6~Ø32	Compact and space saving.
	MCFB	Ø6~Ø20	Compact and space saving. Flush fitting sensor.

MINIATURE CYLINDERS

Image	Model	Specification	Application	DataSheet
	MCMA	Ø16~Ø40	Non-Lubrication High quality long service lifes Magnetic as standard.
	MCMB	Ø20~Ø40	Non-lubrication High quality-long service life Cylinder mountings Standard with magnet
	MCKMB No Rotating	Ø20~Ø40	Non lubrication High quality long service life	Download
	MCMBL End Lock	Ø40	Non-Lubrication High quality long service life Magnetic as standard	Download
	MCMI	Ø16~Ø25	Non-Lubrication High quality long service life Magnetic as standard	Download
	MCKMI	Ø20~Ø25	Non-Lubrication High quality long service life ISO 6432 standard Magnetic as standard	Download
	MCMJ	Ø6~Ø16	High quality long service life Cylinder mountings	Download
	MCMJ1	Ø4	All this product line is without magnet	Download
	MCMJP	Ø6~Ø16	Space saving, compact design enables simple mounting. Flush fitting sensor switch.	Download
	MCMJPB / MCMJPS	Ø6~Ø15	A short stroke miniature cylinder with a shorter overall length.	Download
	MCCG (mm)	Ø20~Ø63	Many mounting options available. Interchangeable with other manufacturers.	Download
	MCCN (inch)	Ø20~Ø63	Many mounting options available. Interchangeable with other manufacturers.	Download

GUIDE CYLINDERS

Image	Model	Specification	Application	DataSheet
	MCGA STOP / LIFT / PUSH type	Ø6~Ø20	Strong cylinder capable of high loads, used extensively for stopping work carriers in both the vertical and horizontal position. Large diameter guide rods enable cylinder to take high off-set loads. Can be used as 90 degree pusher on large conveyor systems. Magnetic as standard.	Download
	MCGS	Ø6~Ø10 Ø12~Ø63	Proven track record in manufacturing precision guided cylinders. Multi-Ports as standard enabling two direction mounting option. Non-rotating accuracy ± 0.1° (φ6, 10 mm). Flush fitting sensors. Inbuilt high density rubber pad absorbs energy at the end of stroke. Magnetic as standard.	Download
	MCGB	Ø12~Ø32	Proven track record in manufacturing precision guided cylinders. Multi-Ports as standard enabling two direction mounting option. Flush fitting sensors. Inbuilt high density rubber pad absorbs energy at the end of stroke. Magnetic as standard.	Download
	MCGI	Ø20~Ø100	Higher loading capacity compared to unguided standard compact cylinders. Wide range of bore sizes and strokes. Ultra compact, light weight and space saving. Sensor slots on RCI sides for flush mounting of proximity sensors. Magnetic as standard.	Download
	MCGD	Ø12~Ø32	Can be used as plate slide type or body slide type. The air cylinder and guide share a compact design which enables the cylinder to work smoothly along its stroke. The cylinder is extremely rigid and strong. Flush fitting sensor available. Magnetic as standard.	Download
	MCG3	Ø63~Ø80	Three guide rods equally spaced enable consistent movement even when uneven load is applied. Increases productivity on conveyor lines. When connected to a rotary actuator the unit can be used as an auto turn lifter. Magnetic as standard.	Download
	MCDA	Ø6~Ø32	Compact in width and length with precision guidance. High lateral loads can be applied on both slide and linear bearing unit. Non rotation is standard. Magnetic as standard.	Download
	MCDB	Ø10~Ø32	Compact in width and length with precision guidance. High lateral loads can be applied on both slide and linear bearing unit. Can be used as body or end plate sliding mechanism. Can have shock absorbers fitted enabling absorption of high loads with low noise.	Download
	MCDJ	Ø6~Ø10	Compact in width and length with precision guidance. High lateral loads can be applied on both slide and linear bearing unit. Magnetic as standard	Download

ROTARY ACTUATOR

Image	Model	Specification	Application	DataSheet
	MCRA	Φ63	Compact profile design Easy to adjust sensor postion High allowable kinetic energy Magnetic as standard	Download
	MCRB	Φ16-Φ32	Dual piston design with rack and pinion structure Adjustable rotation range (0° ~ 190°) Three mounting direction Easy to adjust sensor position Magnetic as standard	Download
	MCRJ	Φ6,8	Dual piston design with rack and pinion Adjustable rotation range (0° ~ 190°) Three mounting direction Easy to adjust sensor position Magnetic as standard	Download
	MCRQ	Φ12-Φ40	Built-in center hole and locating hole for postioning Adjustable rotation range.(0°~190°) Dual piston design with rack and pinion structure Hollow middle rod for easy piping and wiring Selectable shock absorber for higher allowable kinetic energy Easy to install working plane	Download
	MCRQ-S	Φ16-Φ25	Allowable kinetic energy are 4 to 10 times more than MCRQ Shorter profile length compare with MCRQ The required installation space of piston axial direction is decreased due to there is no adjusting bolt or internal shock absorber	Download

STOPPER CLINDERS

Image	Model	Specification	Application	DataSheet
	MSBD	Ø32~20		Download
	MSBD	Ø50~30		Download
	MSBD	Ø65~30 / Ø80~40		Download
	MSBR	Ø20~20 / Ø32~20		Download
	MSBR	Ø40~30 / Ø50~30		Download
	MSBS	Ø20~10 / Ø32~20 / Ø50~30		Download
	MSAR	Ø32~30 / Ø50~30 / Ø80~30		Download
	MSLP-P / CP	Ø32~40		Download
	MSLL	Ø25~30 / Ø40~30		Download
	MSLD	Ø50~50		Download

HYDRAULIC CYLINDERS

Image	Model	Specification	Application	DataSheet
	Double Acting Cylinder	MDHB / MDHD / MDHN		Download
	Double Acting Cylinder-with magnet	MDMB / MDMD /MDMN		Download
	Compact Hydraulic Cylinder	MHCB / MHCQ		Download
	Compact Hydraulic with Piston Sensing Cylinder	MHCB-M / MHCB-MZ		Download
	Manifold type Hydraulic Cylinder	MHCBR / MHCBF / MHCBS		Download
	Hydraulic with Piston Sensing Cylinder	MDOC / MDOA / MDOD / MDON		Download
	Hydraulic Rotary Actuator	MRPH		Download
	Hydraulic Lever-type Cylinder	MHCK MHCK / MHCK-F		Download
	Hydraulic - Swing Clamp Cylinder	MTHS/ MTHD / MHTS / MHTSD		Download
	High oil pressure Swing clamping Cylinder	MFS / MFT / MDS / MDT		Download
	Threaded-body Cylinder	MTC MTS-**A/B		Download
	Hydraulic Work Support	MSO MSP-**A/B		Download

CLAMP CYLINDERS

Image	Model	Specification	Application	DataSheet
	MCKC	12-40	Built-in counterbore design for mounting without additional bracket Easy to adjust sensor position Selectable clamping lever Magnetic as standard	Download
	MAS / MATS	Φ25-Φ63	No additional bracket is required while mounting Selectable clamping lever, include single side type and double side type Magnetic as standard	Download
	MASD / MATSD	32-Φ63	No additional bracket is required while mounting Selectable clamping lever, include single side type and double side type Magnetic as standard	Download
	MCKA	Φ40	Self-lubricating bush and wearing ring for longer lifetime Multiple piping location Magnetic as standard	Download
	MCKG	Φ50-Φ63	Self-lubricating bush and wearing ring for longer lifetime Multiple piping location Multiple piping location	Download
	MCKD	Φ50-Φ63	Oval piston design for space saving Clamping arm angle is adjustable via adjusting bolt with ease. 12 types of clamping arm for various usage 15° mininum release angle for lowering clamping time Welding slag and magnetic field proof sensor is available Cylinder remains clamping position with self-locking mechanism even the air source is off	Download
	MCKB	Φ32	Lever type clamp cylinder gives high clamping force Simple mounting of sensors on all four sides of body Hard anodised body gives smooth lines and high corrosion resistance	Download

RODLESS CYLINDERS

Image	Model	Specification	Application	DataSheet
	MCRPL	Ø16-Ø63	50% space saving when compared to conventional cylinders Multi ported endcaps as standard Reed switches available Magnetic as standard	Download
	MCRPLK	Ø16-Ø40	50% space saving when compared to conventional cylinders End caps with 3 air connections and adjustable cushioning Load strength is higher than MCRPLF series (about 4 Multiple) Magnetic as standard	Download
	MCRPLS	Ø32-Ø63	High resistance to wear Low weight Ability to take high loads & moments in all directions Ability to take shock loadings and vibrations against blows and vibrations	Download
	MCRPM	Ø10-Ø40	50 % space saving. Magnetic transit design Magnetic force transits the movement with piston side magnet and slider magnet Stainless tube, light weighted and durable All series are without switch types	Download
	MCRPMD	Ø10-Ø32	50 % space saving. Magnetic transit design Magnetic force transits the movement with piston side magnet and slider magnet Stainless tube, light weighted and durable	Download
	MCRPMS	Ø10-Ø25	50 % space saving. Magnetic transit design Magnetic force transits the movement with piston side magnet and slider magnet Stainless tube, light weighted and durable The overall design of the cylinder and guide rods, can direct bear loads	Download

AIR UNITS

Image	Model	Specification	Application	DataSheet
	MAC	F.R.L UNIT
	MAFR	F.R. UNIT
	MAF	FILTER
	MAD	AUTO DRAINER
	FMRF/MADV	AUTO DRAIN VALVES
	MAR	PRESSURE REDUCING VALVES
	MAIR	PRECISION REGULATOR
	MAL	LUBRICATOR
	MAF	MICRO MIST FILTER
	MAVS	SOFT START UP VALVE

Accessories

Image	Model
	Fittings
	Vacuum Cups
	Jet Coolers
	Vacuum Generator
	Tubes
	Reed Switches
	Shock Absorbers
	Flow Control
	Pressure Sensor